| Power supply | 120-240 V AC, 8.5 A, 50/60 Hz |
| Power consumption | 720 W (735 VA t 120 V AC)
(0.3 W*1 when standby mode set to eco,*2)
3 W*1 when standby mode set to normal |
| DLP™ chip | Panel Size | 17.0mm (0.67 in) diagonal (16:10 aspect ratio) |
| Display method | DLP™ chip x1, DLP™ projection system |
| Pixels | 2,304,000 (1,920 x 1,200) pixels |
| Lens | PT-RZ670 | Powered zoom (throw ratio 1.7-2.4:1), powered focus F 1.7-1.9, f 25.6-35.7 mm |
| PT-RZ670 | Optional powered zoom/focus and fixed-focus lens |
| Light source | Laser diodes |
| Screen size (diagonal) | 1.27-15.24m (50-600 in), 1.27-5.08m (50-200 in) with the ET-DLE055, 2.54-8.89m (100-350 in) with the ET-DLE030, 16:10 aspect ratio |
| Brightness*3 | 6,500 lm (operating mode: normal) |
| Center-to-corner uniformity*3 | 90% |
| Contrast*3 | 10,000:1 (full on/full off, with dynamic contrast on) |
| Resolution | 1,920 X 1,200 pixels |
| Scanning frequency | SDI | 3G-SDI | SMPTE ST 424 compliant,
[RGB 4:4:4 12-bit/10-bit]
1080(1125)/60i, 1080(1125)/50i,
1080(1125)/25p, 1080(1125)/24p,
1080(1125)/24sF, 1080(1125)/30p,
[YPBPR 4:2:2 10-bit]
1080(1125)/60p, 1080(1125)/50p
|
| HD-SDI | SMPTE ST 292 compliant,
[YPBPR 4:2:2 10-bit]
720(750)/60p, 720(750)/50p,
1035(1125)/60i, 1080(1125)/60i,
1080(1125)/50i, 1080(1125)/25p,
1080(1125)/24p, 1080(1125)/24sF,
1080(1125)/30p |
| SD-SDI | SMPTE ST 259 compliant,
[YCBCR 4:2:2 10-bit]
480i(525i), 576i(625i) |
| HDMI/DVI/DIGITAL LINK | Compatible with HDCP, 480i(525i),*5 576i(625i),*5 480p(525p),
576p(625p), 720(750)/60p, 720(750)/50p, 1080(1125)/60i, 1080(1125)/50i,
1080(1125)/25p, 1080(1125)/24p, 1080(1125)/24sF, 1080(1125)/30p,
1080(1125)/60p, 1080(1125)/50p, VGA (640 x 480)-WUXGA*6 (1,920 x 1,200)
(compatible with non-interlaced signals only), dot clock: 25-162 MHz. |
| RGB | fH: 15-100 kHz, fV: 24-120 Hz, dot clock: 25-162 MHz. |
| YPBPR (YCBCR) | fH: 15.75 kHz, fV: 60 Hz [480i (525i)]
fH: 15.63 kHz, fV: 50 Hz [576i (625i)]
fH: 45.00 kHz, fV: 60 Hz [720 (750)/60p]
fH: 33.75 kHz, fV: 60 Hz [1035 (1125)/60i]
fH: 28.13 kHz, fV: 50 Hz [1080 (1125)/50i]
fH: 27.00 kHz, fV: 24 Hz [1080 (1125)/24p]
fH: 33.75 kHz, fV: 30 Hz [1080 (1125)/30p]
fH: 56.25 kHz, fV: 50 Hz [1080 (1125)/50p]
fH: 31.50 kHz, fV: 60 Hz [480p (525p)]
fH: 31.25 kHz, fV: 50 Hz [576p (625p)]
fH: 37.50 kHz, fV: 50 Hz [720 (750)/50p]
fH: 33.75 kHz, fV: 60 Hz [1080 (1125)/60i]
fH: 28.13 kHz, fV: 25 Hz [1080 (1125)/25p]
fH: 27.00 kHz, fV: 48 Hz [1080 (1125)/24sF]
fH: 67.50 kHz, fV: 60 Hz [1080 (1125)/60p] |
| Video/YC | fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60],
fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM] |
| Optical axis shift*7 | Vertical | +60%, -16%
from center of screen (powered) |
| Horizontal | +30%, -10% (+28%, -10% with the ET-DLE085/DLE080)
from center of screen (powered) |
| Keystone correction range | Vertical: ±40°*8 , horizontal: ±15°*9 |
| Installation | Ceiling/floor, front/rear |
| Terminals | SDI IN | BNC x 1 (3G/HD/SD-SDI) |
| HDMI IN | HDMI 19-pin x1 (Deep Colour, compatible with HDCP) |
| DVI-D IN | DVI-D 24-pin x1 (DVI 1.0 compliant, complatible with HDCP, compatible with single link only) |
| RGB 1 IN | BNC x 5 (RGB/YPBPR/YCBCR/YC x 1) |
| RGB 2 IN | D-Sub HD 15-pin (female) x 1 (RGB/YPBPR/YCBCR x 1) |
| Serial IN | D-sub 9-pin (female) x 1 for external control (RS-232C compliant) |
| Serial Out | D-sub 9-pin (male) x 1 for link control |
| Remote 1 IN | M3 x 1 for wired remote control |
| Remote 1 Out | M3 x 1 for link control (for wired remote control) |
| Remote 2 IN | D-sub 9-pin (female) x 1 for external control (parallel) |
| LAN/Digital link | RJ-45 × 1 (for network and DIGITAL LINK (video/network/serial control) connection,
100Base-TX, compatible with Art-Net,
compliant with PJLink™, Deep Color, compatible with HDCP) |
| Cabinet materials | Molded plastic |
| Dimensions | PT-RZ670 | 498 x 200*14 x 581 mm (19-19/32 x 7-7/8*14 x 22-7/8 in) (with supplied lens) |
| PT-RZ670L | 498 x 200*14 x 538 mm (19-19/32 x 7-7/8*14 x 21-3/16 in) (without lens) |
| Weight | PT-RZ670 | Approximately 23.2 kg (51.1 lbs) (with supplied lens) |
| PT-RZ670L | Approximately 22.5 kg (49.6 lbs) (without lens) |
| Noise level | 35 dB |
| Operating environment | Operating temperature: 0-45 °C (32-113 °F)*16,
operating humidity: 10-80 % (no condensation) |
| Applicable software | Logo Transfer Software, Multi Projector Monitoring & Control Software, Geometry Manager Pro (included in the ET-UK20) |
| Supplied accessories | Multi Projector Monitoring & Control Software
Power cord with secure lock, wireless/wired remote control unit,
batteries (R03/AAA type x 2), software CD-ROM (Logo Transfer Software,
Multi Projector Monitoring & Control Software) |
| NOTE | *1 In STANDARD/GRAPHIC picture mode. Measured based on the power consumption rate and a measurement method for the TV receiver.
*2 When the standby mode is set to ECO, network functions such as power on over the LAN will not operate. Also, only certain commands can be received for external control using the serial terminal.
*3 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*4 Input signals that exceed this resolution will be converted to 1,280 x 800 pixels.
*5 Only compatible with dot clock frequency of 27 MHz (pixel repetition signal).
*6 WUXGA resolution is supported only when the signals are compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).
*7 Optical axis shift cannot be operated with the ET-DLE055, and the optical axis is fixed with the ET-DLE030.
*8 ±22°with the ET-DLE085/DLE055 and +5° with the ET-DLE030.
*9 Cannot be operated with the ET-DLE030.
*10 ±30°with the ET-DLE085/DLE055.
*11 ±40°with the ET-DLE150/DLE250/supplied lens and ±22°with the ET-DLE085/DLE055.
*12 Up to a total of ±55°during simultaneous horizontal and vertical correction.
*13 ±15°with the ET-DLE085/DLE055.
*14 With legs at shortest position.
*15 Average value. May differ depending on models.
*16 When used in locations from 0 m to 4,200 m (0 ft to 13,780 ft) above sea level in NORMAL mode, and from 0 m to 2,700 m (0 ft to 8,858 ft) above sea level in other modes. If the ambient temperature exceeds 35°C (95°F) when used in locations from 0 m to 2,700 m (0 ft to 8,858 ft) above sea level, or if it exceeds 25°C (77°F) when used in locations from 0 m to 4,200 m (0 ft to 13,780 ft) above sea level, the light output may be reduced to protect the projector. |
| NOTES ON USE | 1 Do not install the projector in locations that are subject to excessive water, humidity, steam, or oily smoke. Doing so may result in fire, malfunction, or electric shock.
2 Please observe the following precautions:
• Never place objects on top of the projector while it is in operation.
• Make sure there is an unobstructed space of 500 mm (1 ft 8 in) or more around the projector’s exhaust openings.
• Do not stack projector units directly on top of one another for the purpose of multiple (stacked) projection. When stacking projector units, be sure to provide the amount of space indicated below between them. These space requirements also apply to installations where only one projector unit is operating at one time and the other unit is used as a backup.
• Make sure that nothing blocks the projector’s air intake and exhaust openings. Also, install the projector so that cool or hot air from other air conditioning equipment does not flow directly toward the projector’s air intake or exhaust openings.
• Do not install the projector in an enclosed space. If it is necessary to install it in an enclosed space, add a separate ventilation system. If ventilation is insufficient, hot air will accumulate at the intake opening. This may cause the projector’s protective circuit to interrupt projector operation.
• If the projector is placed in a box or enclosure, ensure the projector’s intake and exhaust openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is not sucked into the intake.3 Because the ET-DLE055/DLE030 is a fixed short-throw lens, the lens shift function cannot be used with it. |
